Every source, one system
PV, battery, genset and grid coordinated as a single site, monitored and controlled together, not as four islands.
Solutions · Energy
Control and monitor solar, wind, genset, storage and grid as one system
NeoTAQ does not just watch your sites — it runs them with solar data logging, hybrid solar diesel control and BESS dispatch on one hybrid energy management system. Solar SCADA and PV monitoring software for grid export limits, genset monitoring and DG controller logic — mixed-brand equipment across Asia, the GCC, Southeast Asia and off-grid solar Africa.
100 MW+solar capacity already monitored on neoSphere
Grid-Tied Solar
Solar–Generator Hybrid
Solar + Storage
Full Hybrid Microgrid
Off-Grid & Remote
Measure
NeoTAQ monitors and controls hybrid energy sites (PV, BESS, genset and grid) with solar O&M software and energy asset management — coordinating sources with neoSync, neoES and neoCore. Solar monitoring GCC deployments and solar monitoring Southeast Asia fleets run from one platform.
Four energy sources, none of them talking to each other
-
Four sources, four islands
PV, gensets, storage and the grid each optimise for themselves, so the whole site runs harder, and costs more, than it should.
-
Solar and the genset fight each other
Push too much PV onto a running generator and it reverse-power trips or wet-stacks; curtail too cautiously and you throw away yield.
-
One export breach erases the savings
Cross the limit in your grid agreement once and the penalty wipes out what the site was earning.
-
Every box speaks a different protocol
Inverters, genset controllers and BMS each talk their own dialect, so there is no single view, let alone single control.
Manage
How NeoTAQ runs a hybrid energy site
-
Grid control that stays compliant
Zero Export, Minimum Import or Maximum Export, enforced in real time at the point of connection. Your limits, never breached.
-
Genset protection and efficiency
Hold every genset above its minimum loading, ramp PV gently, and start or stop on demand. No reverse-power, no wet-stacking.
-
Battery dispatched on what pays
Charge and discharge for peak shaving, self-consumption or genset support, always within safe state-of-charge and power limits.
-
Compatible with the equipment on site
One platform across mixed-brand PV inverters, genset controllers and BMS/PCS: Modbus RTU/TCP and OPC UA, no rip-and-replace.
-
One plant or a whole fleet
Live status, performance and remote control for a single site or your entire portfolio, in one view.
One platform, whatever is on your site
Pick your configuration. NeoTAQ monitors and controls each one with the right logic, across mixed-brand equipment.
Grid-tied solar: export exactly what your agreement allows
A grid-tied plant lives or dies on its connection agreement. Export one kilowatt too many and the penalty lands; curtail too hard and you give away yield.
-
Export compliance, enforced live
Zero Export, Minimum Import or Maximum Export, held in real time at the point of connection. The limit is never breached. -
Steady, never hunting
The setpoint holds accurately even with noisy meters or several feeders, with no overshoot. -
Grid-code ready
Active and reactive power managed to meet power-factor and grid-code requirements. -
Every string in view
Inverters, strings and meters live on neoSphere, so lost yield shows up the day it starts.
Solar–generator hybrid: maximum solar, without risking the genset
Put too much solar onto a running generator and it reverse-power trips or wet-stacks. Curtail too cautiously and you burn diesel you did not need to.
-
Genset minimum-loading control
Every generator is held above its safe minimum loading; PV is curtailed only as much as the engine actually demands. -
Reverse-power and wet-stacking protection
PV ramps gently enough that the engine always keeps up. No reverse-power trips, no wet-stacking. -
Built for multiple gensets
Each unit is protected to its own minimum, with generators brought in and out as the load requires. -
Harvest every safe kilowatt
Solar runs as high as the situation safely allows, so the generator runs less and burns less fuel.
Solar-plus-storage: the battery dispatched on what pays
A battery is only worth the controller deciding when to use it. Charge at the wrong moment, or sit on stored energy when it is valuable, and the asset never pays back.
-
Self-consumption
Surplus solar is stored and released when generation drops, so more of your own energy is used on site. -
Peak shaving
The battery discharges to cap site demand below a target and recharges off-peak, trimming demand charges. -
Export and import control
Charge to absorb would-be export, discharge to avoid costly import, always inside your grid limits. -
The pack, protected
State-of-charge, power, voltage and temperature limits are enforced on every control cycle.
Full hybrid microgrid: every source coordinated as one
Four sources, each pulling its own way. Without one brain coordinating them, compliance, fuel and uptime all suffer at once.
-
One control brain
Solar, grid, generator and battery (and wind where present) coordinated on one platform, not four separate systems. -
Source-aware control
NeoTAQ recognises whether the site is on grid, generator, both or neither, and adapts its control logic automatically. -
Safety first
On any fault the site ramps to a safe state and recovers on its own once stable; brief communication glitches are ridden through. -
Tuned to the site
Limits, ramp rates and thresholds are configured per installation, with safe defaults and no software changes.
Off-grid and remote: keep the lights on with less fuel
With no grid to fall back on, every decision is a trade-off: run the generator too much and fuel costs soar; lean too hard on the battery and you risk an outage.
-
Solar first
NeoTAQ uses solar whenever it is available and calls on the generator only when it is genuinely needed. -
Storage carries the peaks
The battery covers demand spikes and reduces generator runtime, with a reserve held back for ride-through. -
Designed for the field
The on-site edge runs unattended for years, keeps logging through outages, and back-fills the cloud with zero data loss when the link returns. -
Run it from anywhere
Full status and control of a remote site, without a truck-roll.
Maximize
What a coordinated site gains
Compliance, automatically
Never breach an export or import limit again.
Less diesel, more solar
Gensets stay efficient and the battery earns its keep.
One platform, every brand
Monitor and control mixed-vendor sites in a single view.
Request a Demo
100 MW+solar capacity already monitored on neoSphere
In the field
A hybrid fleet across Pakistan and the UAE, run from one place
Through our partner in Pakistan, NeoTAQ runs hybrid PV, storage and genset assets monitored and managed from one platform, not one plant at a time.
Read the case studyEnergy: questions buyers ask
See NeoTAQ run on sites like yours and get answers mapped to your setup.
What can NeoTAQ do on a hybrid energy site?
It monitors and controls every source as one system (PV, battery storage, gensets and the grid), enforcing your grid export limits, protecting gensets, and dispatching the battery, all on one platform.
Can NeoTAQ control how much PV exports to the grid?
Yes. It enforces a Zero Export, Minimum Import or Maximum Export policy in real time at the point of connection, so a site never breaches its grid agreement.
How does it stop solar reverse-powering a generator?
It holds every genset above its minimum loading and ramps PV gently, so the engine is never back-fed, avoiding the reverse-power trips and wet-stacking that damage generators.
Can NeoTAQ control the battery (BESS), not just monitor it?
Yes. It dispatches charge and discharge for self-consumption, peak shaving, export and import control, generator support and backup reserve, always within safe state-of-charge and power limits.
Can it run a site that switches between grid and generator?
Yes. It continuously recognises the active source (grid, generator, both or neither) and adapts its control automatically, ramping to a safe state on any fault.
Does NeoTAQ work off-grid, without a grid connection?
Yes. It runs off-grid and remote sites on solar, storage and generators, prioritising solar and using the battery to cut generator runtime and fuel.
Which inverter, genset and BMS brands does it work with?
NeoTAQ is vendor-neutral. It connects to mixed-brand PV inverters, genset controllers and BMS/PCS over Modbus RTU/TCP and OPC UA. Tell us what is on site and we will confirm compatibility.
Do I need to replace any equipment to use it?
No. NeoTAQ sits on top of the inverters, gensets, meters and BMS already on your sites; a single on-site edge device collects and centralises the data and applies control.
Does NeoTAQ support solar monitoring in Pakistan?
Yes. NeoTAQ is deployed on solar, hybrid solar-diesel and grid-tied sites across Pakistan. It connects to all major inverter brands, including Huawei, Sungrow, SMA and Schneider, with no rip-and-replace of existing equipment.
Where is NeoTAQ based?
NeoTAQ Systems Limited is headquartered in Masdar City, Abu Dhabi, United Arab Emirates.
What is solar data logging?
Solar data logging is the continuous recording of generation, consumption and grid exchange data from PV inverters, meters and sensors. NeoTAQ's neoCore logs data from every asset on site — solar, BESS, genset and grid — in real time, without replacing existing equipment.
Which solar monitoring software works in the GCC?
NeoTAQ is deployed on solar and hybrid sites across the UAE, KSA, Qatar and the wider GCC, connecting to all major inverter brands with no rip-and-replace.
Is there solar monitoring software available in Africa?
Yes. NeoTAQ covers solar, hybrid and off-grid sites in Sub-Saharan and North Africa including Nigeria, Kenya, Ghana and Egypt. Works on 4G where fixed connectivity is unavailable.
See it on your own plant configuration.
A focused demo on the assets you actually run. No generic walkthrough.
100 MW+solar capacity already monitored on neoSphere